Fits 2002-2003 Lexus ES300 Toyota Camry Full Set Gas Shocks Struts Front Rear

100% brand new in factory original condition. Never been used or installed. Top Quality JAPANESE MADE OIL PISTON SEALS!

Pressurized N2 gas to reduce foaming and aerating. Also to ensure product better performance. Effectively to reduce the effect of traveling over rough ground. Seamless cylinder & sleeves to reduce the possibility of splitting to ensure close contact between the piston & cylinder no leaks to obtain stable damping force.

Precision robotic welding in most of the applications. Powder-coated finish for corrosion resistance and long time service. Hard chromed piston rod micro-cracks chromed surface processed & ultra-precision vertical polishing to ensure smooth contact between the piston rod & seal.

Buckle holes are consistent with the original car in situ for easy & quick installation without any changes. Newer valving technology operates in stages based on the velocity of the car. Compatible with the following vehicles.

4X Shocks Struts (Rear Front Left Right). NOTE: Look just above this product description (Item Specifics) for all part numbers and placement on vehicle. Please check your model carefully to avoid unnecessary trouble? Step 1: Before you lift the vehicle, loosen lug nuts one full turn. Step 2: Jack up vehicle and use jack stands for safety & remove the tire from the rotor. Step 3: Wheel alignment is necessary after strut replacement. Marking the position of all the bolts will help keep the alignment close to original and save time aligning. Use a colored pencil to mark the old strut on the bolt Step 4: Use penetrating oil (such as WD40) to coat any rusted fasteners, let soak for approximately 1 hour. Step 5: (Optional) While waiting for oil to soak, take this time to inspect all other components that may need replacement (brake pads, rotors, brake hoses, ball joints, CV boots, tie rod ends, bushings, sway bars, etc).

Step 6: Remove any brake line or wire attachments from the strut body. Do not disconnect brake lines (if possible)! Opening brake lines will require bleeding of the brake system. Use extreme caution when removing brake lines from your struts, as any damage to your brake line can result in expensive and time consuming repairs.

Step 7: Remove sway bar attached to the strut assembly or control arm. Step 8: Remove the tie rod (only if it attached to the body of the strut, if not leave it attached to the steering knuckle). Step 9: Remove the strut to knuckle bolts at the bottom of the strut.

On some vehicles, the brake caliper and rotor may need to be removed to gain access. Step 10: Remove the upper mounting plate bolts located in the engine or trunk compartment. Do not remove the center retaining nut! It is not safe to unload the spring from the assembly in this position.

Step 11: Carefully remove the old strut assembly from the vehicle. Be very cautious not to let the strut "drop" down on your brake line, rotor or drum. Step 12: Install the new Complete Strut Assembly in the reverse order as above (steps 11-6). Using an anti-seize compound on all fasteners is suggested. Step 13: Carefully double check your work and make sure everything is tightened to manufacturers torque specifications.

Step 14: Replace the tire the rotor and tighten to manufacturers torque specifications. Step 15: Slowly lower the vehicle down after removing the jack stands. Pay very close attention to any odd sounds when the vehicle is lowered onto the new Complete Strut Assemblies.

Step 16: It is very important that you immediately "road test" your vehicle right away to ensure that installation was done properly. Listen and feel for common signs of incorrect installation while driving slowly over speed bumps, rough road or potholes. Set of two front struts and two rear struts. Free return or replacement within 30 days. 14.500"(F), 15.840"(R).

7.250"(F), 8.650"(R). 21.750"(F), 24.490"(R).

14.375"(F), 10.840"(R). 18.1115.357.68 (F), 20.4715.758.27 (R). The note there will NOT be read. The images shown are not the actual item and are for your reference only. 1.30 days return offered for BRAND NEW items only, it starts from the day you received it. We will try our best to resolve any kind of issue. FEEDBACK IS VERY IMPORTANT TO US. For 05-13 Nissan Pathfinder Liftgate Tailgate + 2 Rear Window Lift Supports 4pcs. Both of 2 Fits Civic Coupe Complete Shock Strut w/Spring Assembly Front Kit Pair. For 2016 - 2019 Honda Civic Sedan Mud Flaps Splash Guards Car Fender Mudguard. Air Bags 2500LB For Firestone 255C 1/2"NPT 3/8"-16UNC Pair Air Suspension.

This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Steering & Suspension\Shocks, Struts & Assemblies". The seller is "classic-autoparts" and is located in this country: US.

This item can be shipped to United States.

Brand: CLASSIC-AutoParts
Manufacturer Part Number: C808743APS
Type: Strut
Fitment Type: Direct Replacement
Placement on Vehicle: Left, Right, Front, Rear
Manufacturer Warranty: 1 Year
Features: Sealed
Modified Item: No
Adjustable: No
Gas Charged Shock: Yes
Interchange Part Number: CB334338 ,CB334339 ,CB334340 ,CB334341
Other Part Number: CB71491 ,CB71490 ,CB71492 ,CB71493
Kit or Single Part: Kit
Kit Parts Included: Set of two front struts and two rear struts
Surface Finish: Powder Coat
OE Spec or Performance/Custom: OE Spec
Color: Gloss Black
Return Policy: Free return or replacement within 30 days
Shock Absorber System: Double Pipe
Shock Absorber Type: Gas
Vintage Car Part: No
Material: Steel
Mounting Style: Screw-On
Performance Part: No
Quantity: 4Pcs
Superseded Part Number: Shock and Strut
Universal Fitment: No
Compressed Length: 14.500\
Travel Length: 7.250\
Included Hardware: Mounting Hardware
Item Length: 21.750\
Body Length: 14.375\
Package Dimension (in.): 18.11*15.35*7.68 (F), 20.47*15.75*8.27 (R)
Gross Weight (LB): 54.675