Fits Vehicles of the Following Years and Make. Guaranteed Exact Fit for easy installation. 100% BRAND NEW and tested to meet or exceed OEM specifications.For 2006 2007 2008 Subaru Forester 2.5L Full Set Struts & Shocks Absorbers. Premium ISO/TS 16949 quality - guaranteed highest quality available 4. These are brand new, not used or junkyard parts. Each complete assembly is built to meet or exceed exact OEM specifications. High corrosion resistance and long service life. Steel rod is mirco-polished with double chrome plate. Newer Valving technology operates in stages based on the velocity of the car. Use Teflon bonded piston seal to keep friction down and temperature cooler so that valving stays firmer.
These are guaranteed exact fit and don't require the use of a dangerous spring compressor to swap springs. So they are very easy to install! The struts/shocks are nitrogen gas charged and tuned for each specific vehicle application. And safety of your vehicle!Please consult the compatibility table and specifics above for the correct fitment for your Vehicle. 4X Shocks Struts Front Rear Left Right. Two pakages if the full set is over weight. Step 1: Before you lift the vehicle, loosen lug nuts one full turn.
Step 2: Jack up vehicle and use jack stands for safety & remove the tire from the rotor. Step 3: Wheel alignment is necessary after strut replacement. Marking the position of all the bolts will help.
Keep the alignment close to original and save time aligning. Use a colored pencil to mark the old strut on the bolt. Step 4: Use penetrating oil (such as WD40) to coat any rusted fasteners, let soak for approximately 1 hour. Step 5: (Optional) While waiting for oil to soak, take this time to inspect all other components that may need.
Replacement (brake pads, rotors, brake hoses, ball joints, CV boots, tie rod ends, bushings, sway bars, etc). Step 6: Remove any brake line or wire attachments from the strut body. Do not disconnect brake lines (if possible)! Opening brake lines will require bleeding of the brake system. Use extreme caution when removing brake lines from your struts, as any damage to your brake line can result in.Expensive and time consuming repairs. Step 7: Remove sway bar attached to the strut assembly or control arm. Step 8: Remove the tie rod (only if it attached to the body of the strut, if not leave it attached to the steering knuckle). Step 9: Remove the strut to knuckle bolts at the bottom of the strut. On some vehicles, the brake caliper and rotor. May need to be removed to gain access. Step 10: Remove the upper mounting plate bolts located in the engine or trunk compartment. It is not safe to unload the spring from the assembly in this position. Step 11: Carefully remove the old strut assembly from the vehicle.
Be very cautious not to let the strut "drop" down. On your brake line, rotor or drum. Step 12: Install the new Complete Strut Assembly in the reverse order as above (steps 11-6).
Compound on all fasteners is suggested. Step 13: Carefully double check your work and make sure everything is tightened to manufacturers torque specifications. Step 14: Replace the tire the rotor and tighten to manufacturers torque specifications. Step 15: Slowly lower the vehicle down after removing the jack stands. Pay very close attention to any odd sounds.
When the vehicle is lowered onto the new Complete Strut Assemblies. Step 16: It is very important that you immediately "road test" your vehicle right away to ensure that installation.
Listen and feel for common signs of incorrect installation while driving slowly over speed bumps, rough road or potholes. Strut & Shock Assembly Kit. 15.438"(F), 17.938"(R).
21.125"(F), 25.313"(R). 5.687"(F), 7.375"(R). 14.938"(F), 17.438"(R).International Buyers C Please Note. These charges are the buyers responsibility. Q: How do I return an item? Please contact our customer service before you return an item. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers.
If you are satisfied with the product you received, wish you can leave us a feedback. 2X Front Brake Discs Rotors 4X Ceramic Pads Drill Slot For 02-06 Nissan Altima. Fits Lincoln Navigator 2Pieces Front Upper LH & RH Control Arms Suspension Kit. UTV & ATV Brake System Parts. Nerf Bars & Running Boards.Wheel Stem Air Valve Cap. Splash Guards & Mud Flaps. 4 pcs wheel hub bearing. Fuel Pump for Chevy S10 GMC Sonoma Hombre 4.3L 97-02 for Isuzu Hombre 4.3L 97-20. 2 Bulbs H4 HB2 9003 LED Headlight Kit Combo 2600W 390000LM High Low Beam 6000K. 2pc 3157 4114 4157 LED DRL Driving Daytime Running Light Bulbs 12SMD 6000K White. Low Pressure Electric Fuel Pump 12V Gas Diesel Inline HEP-02A BHEP-02A. For Chevy Silverado GMC Sierra 1500 2500 3500 1999-04 Fuel Pump Module Assembly.
The item "For 2006 2007 2008 Subaru Forester 2.5L Full Set Struts & Shocks Absorbers" is in sale since Friday, June 9, 2017. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Suspension & Steering\Shocks & Struts". The seller is "cn-batteries" and is located in Ontario, California. This item can be shipped to United States.